您好,欢迎访问联智博库

上传文档

当前位置:首页 > 工控技术 > PLC > SoftLogix5800 Controller Installation Instructions

SoftLogix5800 Controller Installation Instructions

  • 小库
  • 29 人阅读
  • 0 人下载
  • 2019-02-20 11:06:00

还剩... 页未读,继续阅读

免费阅读已结束,点击付费阅读剩下 ...

¥ 0 元,已有29人购买

免费阅读

阅读已结束,您可以下载文档离线阅读

¥ 1 元,已有0人下载

付费下载

文档部分内容文本提取

Publication 1789-IN001G-EN-P - June 2005Installation InstructionsSoftLogix5800 ControllerCatalog Number(s) 1789-L10, 1789-L30, 1789-L60Inside . . .ForSee PageAbout the SoftLogix5800 Controller1-3Before You Begin1-5Install RSLinx Software1-5Install the SoftLogix5800 Controller1-5Install the Virtual Backplane1-11Install Communication Device Drivers1-12Install the Windows 2000 Driver for a Motion Card1-12Install the Windows XP Driver for a Motion Card1-15Communicate Over an EtherNet/IP Network1-17Communicate Over a ControlNet Network1-18Communicate Over a DeviceNet Network1-18Troubleshoot the SoftLogix5800 Controller1-19Additional Resources1-202 Installation InstructionsPublication 1789-IN001G-EN-P - June 2005Important User InformationSolid state equipment has operational characteristics differing from those of electromechanical equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls (Publication SGI-1.1 available from your local Rockwell Automation sales office or online at http://www.literature.rockwellautomation.com) describes some important differences between solid state equipment and hard-wired electromechanical devices. Because of this difference, and also because of the wide variety of uses for solid state equipment, all persons responsible for applying this equipment must satisfy themselves that each intended application of this equipment is acceptable.In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages resulting from the use or application of this equipment.The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and requirements associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility or liability for actual use based on the examples and diagrams.No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or software described in this manual.Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell Automation, Inc., is prohibited.Throughout this manual, when necessary, we use notes to make you aware of safety considerations.Identifies information about practices or circumstances that can cause an explosion in a hazardous environment, which may lead to personal injury or death, property damage, or economic loss.Identifies information that is critical for successful application and understanding of the product.Identifies information about practices or circumstances that can lead to personal injury or death, property damage, or economic loss. Attentions help you identify a hazard, avoid a hazard and recognize the consequences.Labels may be located on or inside the equipment (e.g., drive or motor) to alert people that dangerous voltage may be present.Labels may be located on or inside the equipment (e.g., drive or motor) to alert people that surfaces may be dangerous temperatures.WARNINGIMPORTANTATTENTIONSHOCK HAZARDBURN HAZARD Installation Instructions 3Publication 1789-IN001G-EN-P - June 2005About the SoftLogix5800 ControllerWhich SoftLogix controller you have determines how many slots are available in the virtual chassis and how many devices you can install.This ControllerHas This MaximumAvailable Slots1789-L101 SoftLogix5800 controllermemory size limit of 2 Mbytes per controller2 PCI network interface cards, which can be a mix of:(1)•one 1784-PCICS•one 1784-PCIC•one 1784-PCIDS•one EtherNet/IP card(2)no motion support1 1784-SIM moduleno third party virtual backplane module support(1)Even though the 1789-L10 controller supports two PCI network interface cards, each card must be a different network card. You cannot have two of the same cards installed in the computer.(2)EtherNet/IP via PCI bus card or embedded EtherNet/IP port on the PC motherboard.3-slot virtual chassis(3)(3)As of version 12 of the SoftLogix controller, the 1789-L10 controller supports 3 slots in the virtual chassis.1789-L302 SoftLogix5800 controllersmemory size limit of 64 Mbytes per controller5 PCI network interface cards(4)2 1784-PM02AE analog motion cards1 1784-PM16SE SERCOS motion card5 1784-SIM modulesEtherNet/IP supportthird party virtual backplane module support(4)The number of available slots in the virtual chassis is limited by activation level. You can have as many PCI communication cards as you have available slots in the virtual chassis and in the personal computer.5-slot virtual chassis1789-L606 SoftLogix5800 controllersmemory size limit of 64 Mbytes per controller16 PCI network interface cards(4)4 1784-PM02AE analog motion cards4 1784-PM16SE SERCOS motion card16 1784-SIM modulesEtherNet/IP supportthird party virtual backplane module support16-slot virtual chassis4 Installation InstructionsPublication 1789-IN001G-EN-P - June 2005System RequirementsThe following table identifies system requirements for the SoftLogix5800 controller.CategoryRequirementpersonal computerIBM-compatible Pentium 4 1.6 GHz or greater (1)other requirements include:•floppy drive to support the Activation disk•hard disk drive must support bus mastering•you might also need bus-mastering drivers for the PC chip set; for Intel motherboards, this software is called “Application Accelerator”Demanding applications including sequential, motion, and other local applications running on the PC may require a dual CPU to achieve performance requirements.(1)The SoftLogix controller has only been tested and qualified on genuine Intel processors.operating systemSupported operating systems:•Microsoft Windows 2000 with Service Pack 4 (recommended)•Microsoft Windows XP with Service Pack 1 or higher (recommended)RAM256 Mbytes of RAM minimumhard disk space50 Mbytes of free hard disk space (or more based on application requirements)motionprimary 32-bit PCI slotone slot per motion card1784-PM16SE requirements:•maximum of four 1784-PM16SE cards per computer•can associate only one 1784-PM16SE card with one controller1784-PM02AE requirements:•maximum of four 1784-PM02AE cards per computer•maximum of four 1784-PM02AE cards can be associated with one controller•cannot associate a 1784-PM02AE motion card with the same controller as a 1784-PM16SE cardnetworkprimary or extended 32-bit PCI slotone slot per communication cardsupports 1784-PCICS for ControlNetsupports 1784-PCIDS for DeviceNetsupports commercially-available Ethernet port for EtherNet/IPthird party networks through the Rockwell Automation Encompass Programvideo16-color VGA graphics adapter 640 x 480 or greater resolution (256-color 800 x 600 minimum for optimal resolution) Installation Instructions 5Publication 1789-IN001G-EN-P - June 2005Before You BeginBefore you can install the SoftLogix controller you need to:•Log into Windows under an account that is a member of the Administrators user group on the computer where you are installing the SoftLogix controller.To log in as a member of the Administrators group, your user account must be added to the Administrators group on the computer. Ask your system administrator if you need help.•Install or verify that the following Windows services (required by the SoftLogix controller) are running. These services are automatically installed when you install Windows Networking or RAS:–Remote Procedure Call (RPC)–Server–WorkstationIf you are using Windows 2000 or Windows XP, right click on the My Computer icon and select the Manage menu item. This opens the Computer Manager tool. Select the Services and Applications folder to verify that the required services are running.Install RSLinx SoftwareBefore you install the SoftLogix controller, make sure RSLinx is installed on the computer. A separate CD with RSLinx software ships with the SoftLogix controller.Install the SoftLogix5800 ControllerWhen you insert the installation CD into your CDROM drive, the CD automatically begins the Setup program for the controller. If your computer meets the hardware and software requirements for the controller, you can install the controller.1.Make sure RSLinx software is installed on the computer. Shutdown RSLinx software before beginning this installation procedure.2.Insert the SoftLogix installation CD.IMPORTANTIf you have a previous version of the SoftLogix controller already installed on the computer, use Add/Remove Programs to remove that earlier version before installing the current version.

小库

92篇文档

文档介绍: SoftLogix5800 Controller Installation Instructions

评论

发表评论
< /20 > 付费下载 ¥ 1 元

Powered by DS文库

Copyright © 联智博库 All Rights Reserved. 鲁ICP备18004091号-4
×
保存成功