您好,欢迎访问联智博库

上传文档

当前位置:首页 > 工控技术 > 其他 > XL6XL6e OCS Models HE-XL103 HEXT350C113 HE-XL1E3 HEXT351C113 HE-XL104 HEXT350C114 HE-XL1E4 HEXT3

XL6XL6e OCS Models HE-XL103 HEXT350C113 HE-XL1E3 HEXT351C113 HE-XL104 HEXT350C114 HE-XL1E4 HEXT3

  • 文哥
  • 18 人阅读
  • 0 人下载
  • 2019-05-02 11:46:16

还剩... 页未读,继续阅读

免费阅读已结束,点击付费阅读剩下 ...

¥ 0 元,已有18人购买

免费阅读

阅读已结束,您可以下载文档离线阅读

¥ 1 元,已有0人下载

付费下载

文档部分内容文本提取

MAN0886-03-EN Specifications / Installation __________________________________________________________________________________________________________________________________________________________________ 4/28/2009 Page 1 of 6 ECN # 950 1 Specifications Specifications Digital DC Inputs XL103 XL104 Digital DC Outputs XL103 XL104 Inputs per Module 12 including 4 configurable HSC inputs 24 including 4 configurable HSC inputs Outputs per Module 12 including 2 configurable PWM outputs 16 including 2 configurable PWM outputs Commons per Module 1 Commons per Module 1 Input Voltage Range 12 VDC / 24 VDC Output Type Sourcing / 10 K Pull-Down Absolute Max. Voltage 35 VDC Max. Absolute Max. Voltage 28 VDC Max. Input Impedance 10 kΩ Output Protection Short Circuit Input Current Positive Logic Negative Logic Max. Output Current per point 0.5 A Upper Threshold 0.8 mA -1.6 mA Max. Total Current 4 A Continuous Lower Threshold 0.3 mA -2.1 mA Max. Output Supply Voltage 30 VDC Max Upper Threshold 8 VDC Minimum Output Supply Voltage 10 VDC Min Lower Threshold 3 VDC Max. Voltage Drop at Rated Current 0.25 VDC OFF to ON Response 1 ms Max. Inrush Current 650 mA per channel ON to OFF Response 1 ms Min. Load None HSC Max. Switching Rate 10 kHz Totalizer/Pulse,Edges 5 kHz Frequency/Pulse,Width 2.5 kHz Quadrature OFF to ON Response 1 ms Analog Inputs, Medium Resolution XL103 XL104 ON to OFF Response 1 ms Number of Channels 2 2 Output Characteristics Current Sourcing (Pos logic) General Specifications Input Ranges Safe input voltage range Input Impedance (Clamped @ -0.5 VDC to 12 VDC) 0 - 10 VDC 0 – 20 mA 4 – 20 mA -0.5 V to +12V Current Mode: 100 Ω Voltage Mode: 500 k Ω Required Power (Steady State) 500 mA @ 24 VDC Required Power (Inrush) 30 A for 1 ms @ 24 VDC – DC Switched 2.5 A for 4 ms @ 24 VDC - AC Switched Nominal Resolution %AI full scale Max. Over-Current 10 Bits 32,000 counts 35 mA Primary Power Range 10 – 30 VDC Conversion Speed All channels converted once per ladder scan Relative Humidity 5 to 95% Non-condensing Max. Error at 25°C (excluding zero) 4-20 mA 1.00% 0-20 mA 1.00% 0-10 VDC 0.50% Operating Temperature -10°C to +60°C Terminal Type Screw Type,5 mm Removable Additional error for temperatures other than 25°C TBD CE UL See Compliance Table at http://www.heapg.com/Pages/TechSupport/ProductCert.html Filtering 160 Hz hash (noise) filter 1-128 scan digital running average filter Weight 26.5 oz. (.751 kg) Clock Accuracy +/- 35 ppm maximum at 25° C (+/- 1.53 Minutes per Month) Connectivity Serial Ports 2 Serial Ports – RS232 & RS485 Ethernet 10/100-Mbps (XL6e models only) USB USB Networking Port for communication with PCs and programming Port Removable Media Removable Media for upto 2 GB of storage for programs, data logging or screen capture Smartstix Remote IO modules communicating on CAN Note: Highest usable frequency for PWM output is 65 KHz XL6/XL6e OCS Models HE-XL103 / HEXT350C113 HE-XL1E3 / HEXT351C113 Digital DC Inputs / 12 Digital Outputs 2 Analog Inputs (Medium Resolution) XL6/XL6e OCS Models HE-XL104 / HEXT350C114 HE-XL1E4 / HEXT351C114 24 Digital DC Inputs / 16 Digital Outputs 2 Analog Inputs (Medium Resolution) MAN0886-03-EN Specifications / Installation __________________________________________________________________________________________________________________________________________________________________ 4/28/2009 Page 2 of 6 ECN # 950 2 Installation 1. Prior to mounting, observe requirements for the panel layout design and spacing/clearances in the OCS XL6 Series Manual (MAN0883). 2. Cut the host panel. 3. Insert the OCS through the panel cutout (from the front). The gasket material needs to be between the host panel and the OCS. 4. Install and tighten the mounting clips (provided with the OCS) until the gasket material forms a tight seal. 5. Connect cables as needed such as communications, programming, power and CsCAN cables to the ports using the provided connectors. 6. Begin configuration procedures. 3 Panel Cut-Out and Dimensions Note: Max. panel thickness: 5 mm. Refer to the XL6 User Manual (MAN0883) for panel box information and a handy checklist of requirements. Note: The tolerance to meet NEMA standards is ± 0.005” (0.1 mm). Caution: Do not force the OCS into the panel cutout. An incorrectly sized panel cutout can damage the touch screen. HE-XL103/HE-XL104 HE-XL1E3/ HE-XL1E4 001XLQX0076.875”[175mm][131mm]001OCS003-R15.156”R .125” [3 mm] TYP.RADIUS CORNERSWHEN REQUIRINGDUST OR WATERTIGHT SEAL PERNEMA 4, 4X OR 12MAN0886-03-EN Specifications / Installation __________________________________________________________________________________________________________________________________________________________________ 4/28/2009 Page 3 of 6 ECN # 950 4 Ports and Connectors To Remove I/O Cover: Unscrew 4 screws located on the cover. Remove cover. CAUTION: Do not over tighten screws when replacing the back cover. I/O Jumpers: I/O Jumpers (JP) are located internally. To access, remove I/O cover of unit. Wiring Connectors (J1 / J2 / J3 / J4) and I/O Jumpers (JP1 and JP3) are described in the Wiring and Jumpers section of this document. Memory Slot: Uses Removable Memory for data logging, screen captures, program loading and recipes. Horner Part No.: HE-MC1 Serial Communications: MJ1: (RS-232 / RS-485) Used for Cscape programming and Application-Defined Communications. MJ2: (RS-232 / RS-485) Used for Application-Defined Communications. Ethernet: Used for Cscape programming and Application-Defined Communications. MAN0886-03-EN Specifications / Installation __________________________________________________________________________________________________________________________________________________________________ 4/28/2009 Page 4 of 6 ECN # 950 4.2 External DIP Switch Settings MJ2 Pinouts in Half and Full Duplex Modes Table - Ports and Functions Functions Port 1 (MJ1) Port 2 (MJ2) RS-232 ���� ���� Hardware Handshaking ���� X Programming ���� X Ladder function controlled ���� ���� Serial Downloable Protocols ���� ���� RS 485 Full duplex ���� ���� RS485 Half duplex ���� X NET1 Port Pin Assignments Pin Signal Signal Description Direction 1 V- CAN Ground − 2 CN_L CAN Data Low In/Out 3 SHLD Shield Ground − 4 CN_H CAN Data High In/Out 5 NC No Connect − 4.1 Serial Communications: MJ1: (RS-232 / RS-485) Use for Cscape programming and Application-Defined Communications. MJ2: (RS-232 / RS-485) Use for Application-Defined Communications. As seen when looking at the side of the XL6 unit : The DIP Switches are used for termination of the RS-485 ports. The XL6 is shipped un-terminated. To terminate, select one of the DIP Switches and configure it based upon the option that is desired. Pin MJ1 Pins MJ2 Pins Signal Direction Signal Direction 8 TXD OUT TXD OUT 7 RXD IN RXD IN 6 0 V Ground 0 V Ground 5* +5 60mA OUT +5 60mA OUT 4 RTS OUT TX- OUT 3 CTS IN TX+ OUT 2 RX- / TX- IN / OUT RX- IN 1 RX+ / TX+ IN / OUT RX+ IN 1 8 * +5V 60mA Max MJ2 Half Duplex Mode Pin MJ2 Pins Signal Direction 8 TXD OUT 7 RXD IN 6 0 V Ground 5* +5 60mA OUT 4 TX- OUT 3 TX+ OUT 2 TX-/RX- IN/OUT 1 TX+/RX+ IN/OUT 1 8 Pin MJ2 Pins Signal Direction 8 TXD OUT 7 RXD IN 6 0 V Ground 5* +5 60mA OUT 4 TX- OUT 3 TX+ OUT 2 RX- IN 1 RX+ IN 1 8 MJ2 Full Duplex Mode * +5V 60mA Max SW1 - ON enables MJ2 RS485 port termination (121 Ohms). OFF disables MJ2 RS485 port termination. SW2 & SW3 - ON places MJ2 RS485 port in half-duplex mode. OFF places MJ2 RS485 port in full-duplex mode. SW4 - ON enables MJ1 RS485 port termination (121 Ohms). OFF disables MJ1 RS485 port termination. MJ1 MJ2 On Off On Off On Off CAN Connector Use the CAN Connector when using CsCAN network. Torque rating 4.5 – 7 Lb-In (0.50 – 0.78 N-m) Speeds 10 BaseT Ethernet (10-Mbps) 100 BaseTx Fast Ethernet (100-Mbps) Modes Half or Full Duplex Auto-Negotiation Both 10/100-Mbps and Half/Full Duplex Connector Type Shielded RJ-45 Cable Type (Recommended) CAT5 (or better) UTP Port Auto MDI/MDI-X 4.3 CAN Network Port and Wiring 4.4 Ethernet Port MAN0886-03-EN Specifications / Installation __________________________________________________________________________________________________________________________________________________________________ 4/28/2009 Page 5 of 6 ECN # 950 Primary Power Port Pins Pin Signal Description 1 Ground Frame Ground 2 V- Input Power Supply Ground 3 V+ Input Power Supply Voltage 5 Wiring and Jumpers • Wire according to the type of inputs / outputs used and select the appropriate jumper option. • 5.1 I/O Jumpers Settings (JP1 – JP3) 5.2 Wiring Examples J1 Orange XL103 / XL104 Name I1 IN1 I2 IN2 I3 IN3 I4 IN4 I5 IN5 I6 IN6 I7 IN7 I8 IN8 H1 HSC1 / IN9 H2 HSC2 / IN10 H3 HSC3 / IN11 H4 HSC4 / IN12 A1 Analog IN1 A2 Analog IN2 0V Ground J2 Black XL103 XL104 0V Ground V+ V+ * NC No Connect OUT13 Q12 OUT12 Q11 OUT11 Q10 OUT10 Q9 OUT9 Q8 OUT8 Q7 OUT7 Q6 OUT6 Q5 OUT5 Q4 OUT4 Q3 OUT3 Q2 OUT2 / PWM2 Q1 OUT1 / PWM1 V+* Supply for Sourcing Outputs J3 Orange XT104 I13 IN13 I14 IN14 I15 IN15 I16 IN16 I17 IN17 I18 IN18 I19 IN19 I20 IN20 I21 IN21 I22 IN22 I23 IN23 I24 IN24 0V Ground Note: The Cscape Module Setup configuration must match the selected I/O (JP) jumper settings. I10V001XLE03612-24VDCI10VPositive Logic In Negative Logic In Positive Logic vs. Negative Logic Wiring The XL6 can be wired for Positive Logic inputs or Negative Logic inputs. Location of I/O jumpers (JP) and wiring connectors (J1 – J4). Wiring Specifications � For I/O wiring (discrete), use the following wire type or equivalent: Belden 9918, 18 AWG (0.8 mm2) or larger. � For shielded Analog I/O wiring, use the following wire type or equivalent: Belden 8441, 18 AWG (0.8 mm2) or larger. � For CAN wiring, use the following wire type or equivalent: Belden 3084, 24 AWG (0.2 mm2) or larger. Use copper conductors in field wiring only, 60/75° C Negative Logic Positive Logic JP1 Digital DC Inputs Default XL104 J3 Orange Positive Logic Digital In J4 Orange XL104 Q16 OUT16 Q15 OUT15 Q14 OUT14 XL104 J4 Orange Positive Logic Digital Out Q14 Q15 V+ 0V LOAD LOAD 10 - 30VDC Q16 LOAD J2 J4 Note: When using JP3 (A1-A2), each channel can be independently configured. Note: Loop Power requirements are determined by the transmitter specification. 20mA10VDCJP3CURRENT OR VOLTAGE INPUTS001XLE043-R1A1A2A1A211223344I1I2I3I40VI5I6I7I8H1001XLE04612-24VDCLOOPPWR20mA0-10VDCA1A2H2H3H4XL103 / 104 J1 Orange Positive Logic Digital In J1J2J3JP3JP1001XLE005-R1J4Q1Q2Q3Q4Q9Q10Q11Q12Q5Q6Q7Q8V+0VLOADLOADLOADLOADLOADLOADLOADLOADLOADLOADLOADLOAD10 - 30VDCQ13001XLE024LOADXL103 / 104 J2 Black Positive Logic Digital Out I13I14I15I16I22I23I240VI17I18I19I20I21001XLE04712-24VDC4.5 Power Port and Wiring

文哥
文哥
  • 4231

    文档
  • 0

    金币
Ta的主页 发私信

4231篇文档

文档介绍: XL6XL6e OCS Models HE-XL103 HEXT350C113 HE-XL1E3 HEXT351C113 HE-XL104 HEXT350C114 HE-XL1E4 HEXT351C114

评论

发表评论
< /6 > 付费下载 ¥ 1 元

Powered by DS文库

Copyright © 联智博库 All Rights Reserved. 鲁ICP备18004091号-4
×
保存成功