您好,欢迎访问联智博库

上传文档

当前位置:首页 > 工控技术 > PLC > BACnet MSTP User Manual

BACnet MSTP User Manual

  • 文哥
  • 29 人阅读
  • 0 人下载
  • 2019-02-22 23:25:13

还剩... 页未读,继续阅读

免费阅读已结束,点击付费阅读剩下 ...

¥ 0 元,已有29人购买

免费阅读

阅读已结束,您可以下载文档离线阅读

¥ 1 元,已有0人下载

付费下载

文档部分内容文本提取

 BACnet MS/TP Adapter20-COMM-BFRN 1.xxxUser ManualImportant User InformationSolid state equipment has operational characteristics differing from those of electromechanical equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls (Publication SGI-1.1 available from your local Rockwell Automation sales office or online at http://www.rockwellautomation.com/literature) describes some important differences between solid state equipment and hard-wired electromechanical devices. Because of this difference, and also because of the wide variety of uses for solid state equipment, all persons responsible for applying this equipment must satisfy themselves that each intended application of this equipment is acceptable.In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages resulting from the use or application of this equipment.The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and requirements associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility or liability for actual use based on the examples and diagrams.No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or software described in this manual.Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell Automation, Inc. is prohibited.Throughout this manual, when necessary we use notes to make you aware of safety considerations. Important:Identifies information that is critical for successful application and understanding of the product. Allen-Bradley, PowerFlex, DPI, SCANport, DriveExplorer, DriveExecutive, DriveTools SP, and ControlFLASH are either registered trademarks or trademarks of Rockwell Automation, Inc.BACnet is a registered trademark of American Society of Heating, Refrigerating and Air-Conditioning Engineers (ASHRAE).WARNING: Identifies information about practices or circumstances that can cause an explosion in a hazardous environment, which may lead to personal injury or death, property damage, or economic loss.ATTENTION: Identifies information about practices or circumstances that can lead to personal injury or death, property damage, or economic loss. Attentions help you identify a hazard, avoid the hazard, and recognize the consequences.Shock Hazard labels may be located on or inside the equipment (e.g., drive or motor) to alert people that dangerous voltage may be present.Burn Hazard labels may be located on or inside the equipment (e.g., drive or motor) to alert people that surfaces may be at dangerous temperatures. Summary of ChangesThe information below summarizes the changes made to this manual since its last release (May 2006): The information below summarizes the changes made to this manual since its last release (April 2006): Description of ChangesPage(s)In the “Quick Start” section:•In Step 4, removed connecting the adapter to the network.•In Step 5, added two new sub-steps (B and C).•Added a new Step 6 “Connect the adapter to the network.”•Incremented old Steps 6 and 7 to Steps 7 to 8.1-6Reorganized Chapter 2:•Moved the “Connecting the Adapter to the Drive” section after the “Commissioning the Adapter” section.•Moved the “Applying Power” section after the “Connecting the Adapter to the Drive” section.•In the “Applying Power” section, added three new subsections:– “Start-Up Status Indications”– “Verifying/Setting Key Adapter Parameters”– “Configuring/Verifying Key Drive Parameters.”•Moved the “Connecting the Drive/Adapter to the Network” section to the end of the chapter.Chapter 2In Chapter 3, moved the “Setting the Device Instance Number” section after the “Using the PowerFlex 7-Class HIM” section. Included additional information to the “Setting the Device Instance Number” section.3-3Added new Appendix D “Routing Capability for Networked Drives.”D-1Description of ChangesPage(s)In the Features section — first bullet, removed text “... and can be used with the kit’s optional I/O board.” Also, added an Important statement regarding this information.1-2In the Viewing the Adapter Configuration table, added a third bullet in the Parameter 07 - [Baud Rate Act] row.3-8For Parameter 05 - [Flt Cfg Ref], corrected its detail information from being a bit parameter to a numeric parameter.B-2soc-iiSummary of Changes  Table of ContentsPrefaceAbout This ManualRelated Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P-1Rockwell Automation Support. . . . . . . . . . . . . . . . . . . . . . . . P-2Conventions Used in This Manual. . . . . . . . . . . . . . . . . . . . . P-2Chapter 1Getting StartedComponents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2Compatible Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3Required Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4Quick Start. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6Status Indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7Chapter 2Installing the AdapterPreparing for an Installation. . . . . . . . . . . . . . . . . . . . . . . . . . 2-1Commissioning the Adapter. . . . . . . . . . . . . . . . . . . . . . . . . . 2-1Connecting the Adapter to the Drive. . . . . . . . . . . . . . . . . . . 2-6Applying Power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8Connecting the Drive/Adapter to the Network . . . . . . . . . . 2-10Chapter 3Configuring the AdapterConfiguration Tools. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1Using the PowerFlex 7-Class HIM . . . . . . . . . . . . . . . . . . . . 3-2Setting the Device Instance Number . . . . . . . . . . . . . . . . . . . 3-3Setting a Comm Loss Action. . . . . . . . . . . . . . . . . . . . . . . . . 3-5Setting the Comm Loss Time. . . . . . . . . . . . . . . . . . . . . . . . . 3-6Setting the Baud Rate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7Resetting the Adapter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7Viewing the Adapter Configuration. . . . . . . . . . . . . . . . . . . . 3-8Chapter 4Using BACnet ObjectsUnderstanding BACnet Objects. . . . . . . . . . . . . . . . . . . . . . . 4-1Basic Drive Operation on the Network . . . . . . . . . . . . . . . . . 4-2Supported BACnet Objects . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3

文哥
文哥
  • 4231

    文档
  • 0

    金币
Ta的主页 发私信

4231篇文档

文档介绍: BACnet MSTP User Manual

相关搜索

BACnet MSTP User Manual

评论

发表评论
< /76 > 付费下载 ¥ 1 元

Powered by DS文库

Copyright © 联智博库 All Rights Reserved. 鲁ICP备18004091号-4
×
保存成功