您好,欢迎访问联智博库

上传文档

当前位置:首页 > 工控技术 > HMI > Mitsubishi Electric Corporation Q Series CPU Direct

Mitsubishi Electric Corporation Q Series CPU Direct

  • 文哥
  • 14 人阅读
  • 0 人下载
  • 2019-02-20 11:27:55

还剩... 页未读,继续阅读

免费阅读已结束,点击付费阅读剩下 ...

¥ 0 元,已有14人购买

免费阅读

阅读已结束,您可以下载文档离线阅读

¥ 1 元,已有0人下载

付费下载

文档部分内容文本提取

1Mitsubishi Electric CorporationQ Series CPU Direct Driver1System Configuration.......................................................................................................32External Devices Selection..............................................................................................83Communication Settings..................................................................................................94Setup Items....................................................................................................................105Cable Diagram...............................................................................................................146Supported Device...........................................................................................................167Device Code and Address Code....................................................................................258Error Messages..............................................................................................................30Q Series CPU Direct Driver GP-Pro EX Device/PLC Connection Manual2IntroductionThis manual describes how to connect the Display and the External Device (target PLC).In this manual, the connection procedure is described in the sections identified below:1System ConfigurationThis section lists the types of External Devices and SIO that you can connect.�"1 System Configuration" (page 3)2External Devices SelectionSelect the model (series) of the External Device and its connection method.�"2 External Devices Selection" (page 8)3Communication SettingsThis section shows setting examples for communicating between the Display and the External Device.�"3 Communication Settings" (page 9)4Setup ItemsThis section describes communication setup items on the Display.Set the Display's communication settings in GP-Pro EX or in offline mode.�"4 Setup Items" (page 10)5Cable DiagramThis section shows cables and adapters for connecting the Display and the External Device.�"5 Cable Diagram" (page 14)OperationQ Series CPU Direct Driver GP-Pro EX Device/PLC Connection Manual31System ConfigurationThe system configuration in the case when the External Device and the Display are connected is shown.SeriesCPULink I/FSIO TypeSetting ExampleCable DiagramMELSEC QSeriesQ02CPUQ02HCPUQ06HCPUQ12HCPUQ25HCPURS-232C port on CPU unitRS232CSetting Example 1 (page 9)Cable Diagram 1 (page 14)Q00UJCPUQ00UCPUQ01UCPUQ02UCPUQ03UDCPUQ04UDHCPUQ06UDHCPUQ10UDHCPUQ13UDHCPUQ20UDHCPUQ26UDHCPUQ03UDECPUQ04UDEHCPUQ06UDEHCPUQ10UDEHCPUQ13UDEHCPUQ20UDEHCPUQ26UDEHCPUQ03UDVCPUQ04UDVCPUQ06UDVCPUQ13UDVCPUQ26UDVCPURS-232C port on High Performance Model QCPU or Universal Model QCPU *1*2 *1Except Q00UJCPU, Q00UCPU and Q01UCPU.*2Since the Built-in Ethernet port QCPU cannot be directly connected to the Display, use it with a Multi CPU System.Q172HCPURS-232C port on High Performance Model QCPU*3*3Since the motion CPU (Q172HCPU, Q172DCPU, Q173DCPU) cannot be directly connected to the Display, use it with a Multi CPU System.Q172DCPUQ173DCPURS-232C port on Universal Model QCPU*1*3Q Series CPU Direct Driver GP-Pro EX Device/PLC Connection Manual4�Connection Configuration•Single CPU System•Multi CPU System•For CPU's Unit No., No.1 is allocated to the CPU slot and No.2, 3, and 4 are allocated to the other slots from No.1 to right.•With Multi CPU System, it's possible to access a CPU unit that is not directly connected. Regarding the external devices that can be used for Multi CPU System, please refer to the manual of the External Device.•Use the motion CPU within the No. 2 to No. 4 range. The motion CPU cannot be used as No. 1.DisplayExternal DeviceDisplayExternal DeviceNo.1No.2No.3No.4CPU UnitQ Series CPU Direct Driver GP-Pro EX Device/PLC Connection Manual5�IPC COM PortWhen connecting IPC with an External Device, the COM port used depends on the series and SIO type. Please refer to the IPC manual for details.Usable portSeriesUsable PortRS-232CRS-422/485(4 wire)RS-422/485(2 wire)PS-2000BCOM1*1, COM2, COM3*1, COM4*1The RI/5V can be switched. Use the IPC’s switch to change if necessary.--PS-3450A, PS-3451A,PS3000-BA, PS3001-BDCOM1, COM2*1*2COM2*1*2COM2*1*2PS-3650A (T41 model),PS-3651A (T41 model)COM1*1--PS-3650A (T42 model),PS-3651A (T42 model)COM1*1*2, COM2COM1*1*2COM1*1*2PS-3700A (Pentium®4-M)PS-3710ACOM1*1, COM2*1, COM3*2, COM4*2Set up the SIO type with the DIP Switch. Please set up as follows according to SIO type to be used.COM3*2COM3*2PS-3711ACOM1*1, COM2*2COM2*2COM2*2PS4000*3*3When making communication between an External Device and COM port on the Expansion slot, only RS-232C is supported. However, ER (DTR/CTS) control cannot be executed because of the specification of COM port. For connection with External Device, use user-created cables and disable Pin Nos. 1, 4, 6 and 9. Please refer to the IPC manual for details of pin layout.COM1, COM2--PL3000COM1*1*2, COM2*1, COM3, COM4COM1*1*2COM1*1*2PE-4000B Atom N270COM1, COM2--PE-4000B Atom N2600COM1, COM2COM3*4, COM4*4, COM5*4, COM6*4*4Set up the SIO type with the BIOS. Please refer to the IPC manual for details of BIOS.COM3*4, COM4*4, COM5*4, COM6*4PS5000 (Slim Panel Type Core i3 Model) *5 *6COM1, COM2*4COM2*4COM2*4PS5000 (Slim Panel Type Atom Model) *5 *6COM1, COM2*7COM2*7COM2*7PS5000 (Enclosed Panel Type)*8COM1--PS5000 (Modular Type) *5 *6COM1*7COM1*7COM1*7

文哥
文哥
  • 4231

    文档
  • 0

    金币
Ta的主页 发私信

4231篇文档

文档介绍: Mitsubishi Electric Corporation Q Series CPU Direct

评论

发表评论
< /30 > 付费下载 ¥ 1 元

Powered by DS文库

Copyright © 联智博库 All Rights Reserved. 鲁ICP备18004091号-4
×
保存成功