您好,欢迎访问联智博库

上传文档

当前位置:首页 > 工控技术 > HMI > CC-Link Partner Association CC-Link Intelligent Device

CC-Link Partner Association CC-Link Intelligent Device

  • 文哥
  • 34 人阅读
  • 0 人下载
  • 2019-02-20 11:25:03

还剩... 页未读,继续阅读

免费阅读已结束,点击付费阅读剩下 ...

¥ 0 元,已有34人购买

免费阅读

阅读已结束,您可以下载文档离线阅读

¥ 1 元,已有0人下载

付费下载

文档部分内容文本提取

1CC-Link Partner AssociationCC-Link Intelligent Device Driver1System Configuration.......................................................................................................42Selection of External Device..........................................................................................113Example of Communication Setting...............................................................................124Setup Items....................................................................................................................295Cable Diagram...............................................................................................................336Supported Devices.........................................................................................................357Device Code and Address Code....................................................................................408Error Messages..............................................................................................................43CC-Link Intelligent Device DriverGP-Pro EX Device/PLC Connection Manual2IntroductionThis manual describes how to connect the Display and the External Device (target PLC).In this manual, the connection procedure will be described by following the sections below:1System ConfigurationThis section shows the types of External Devices which can be connected and SIO type.�"1 System Configuration" (page 4)2Selection of External DeviceSelect the model (series) of the External Device to be connected and its connection method.�"2 Selection of External Device" (page 11)3Example of Communication SettingsThis section shows setting examples for communicating between the Display and the External Device.�"3 Example of Communication Setting" (page 12)4Setup ItemsThis section describes communication setup items on the Display.Set the communication settings of the Display with GP-Pro EX or in offline mode.�"4 Setup Items" (page 29)Operation5Cable DiagramThis section shows cables and adapters for connecting the Display and the External Device.�"5 Cable Diagram" (page 33)CC-Link Intelligent Device DriverGP-Pro EX Device/PLC Connection Manual3�TerminologyThe following table describes the terminology used in the CC-Link.TermDefinition and DescriptionCyclic TransmissionA function that periodically exchanges data across the network connected to the CC-Link.Extended Cyclic TransmissionA function that periodically exchanges up to 128 pieces of bit data and up to 64 pieces of word data per station using split transfer. Available to CC-Link Ver 2.00 or later.Extended Cyclic SettingUsed for extending the cyclic points in the extended cyclic transmission. Select 2, 4, or 8 times.Transient TransmissionA function that exchanges data across the network connected to the CC-Link only when the data is requested.Master StationA station that controls the entire network with control information (parameters). Set one station per network. The station No. is "0".Slave StationA generic name for stations other than the master station.Intelligent Device StationA station that performs the cyclic transmission and the transient transmission for the master station in the ratio of 1:n.Number of Occupied StationsThe number of stations on the network that one slave station occupies. Select one to four stations depending on the number of data.CC-Link Intelligent Device DriverGP-Pro EX Device/PLC Connection Manual41System ConfigurationThe following shows the system configuration where the External Device from Mitsubishi Electric Corporation and the Display are connected.SeriesCPULink I/FCommunication TypeSetting ExampleCable DiagramMELSEC ASeriesA1SCPUA1SHCPUA1SJCPUA1SJCPU-S3A1SJHCPUA1SCPU24-R2A2SCPUA2SHCPUA2USCPUA2USCPU-S1A2USHCPU-S1A1SJ61BT11CC-Link Ver.1.1Setting Example 1 (page 12)Cable Diagram 1 (page 33)A0J2CPUA0J2HCPUA1CPUA2CPUA2CPU-S1A3CPUA1NCPUA2NCPUA2NCPU-S1A3NCPUA3MCPUA3HCPUA2ACPUA2ACPU-S1A3ACPUA2UCPUA2UCPU-S1A3UCPUA4UCPUAJ61BT11MELSEC QnASeriesQ2ASCPUQ2ASCPU-S1Q2ASHCPUQ2ASHCPU-S1A1SJ61QBT11CC-Link Ver.1.1Setting Example 2 (page 15)*1Cable Diagram 1 (page 33)Setting Example 3 (page 18)*2Q2ACPUQ2ACPU-S1Q3ACPUQ4ACPUQ4ARCPUAJ61QBT11CC-Link Ver.1.1Setting Example 2 (page 15)*1Setting Example 3 (page 18)*2CC-Link Intelligent Device DriverGP-Pro EX Device/PLC Connection Manual5MELSEC QSeriesQ00JCPUQ00CPUQ01CPUQ02CPUQ02HCPUQ06HCPUQ12HCPUQ25HCPUQ12PHCPUQ25PHCPUQ12PRHCPUQ25PRHCPUQJ61BT11NCC-Link Ver.1.1Setting Example 4 (page 21)Cable Diagram 1 (page 33)CC-Link Ver.2.0Setting Example 5 (page 23)QJ61BT11CC-Link Ver.1.1Setting Example 4 (page 21)Q02CPU-AQ02HCPU-AQ06HCPU-AA1SJ61BT11CC-Link Ver.1.1Setting Example 1 (page 12)Q02UCPUQ03UDCPUQ04UDHCPUQ06UDHCPUQJ61BT11NCC-Link Ver.1.1Setting Example 4 (page 21)CC-Link Ver.2.0Setting Example 5 (page 23)MELSEC LSeriesL26CPU-BTCC-Link terminal block on CPU unitCC-Link Ver.1.1Setting Example 6 (page 25)CC-Link Ver.2.0Setting Example 7 (page 27)*1Use the ladder program for communication settings. Available to all feature versions of the Link I/F.*2Configure the communication settings in [Network Parameter] in the ladder software (GX-Developer).Available to feature version B or later of the Link I/F. Check the feature version on the nameplate located onthe side of the Link I/F unit.•To use the CC-Link, you need a CC-Link unit (CA7-CCLALL/EX-01) from Pro-face. For details on the wiring between the Display (CC-Link unit) and the CC-Link master and on the CC-Link unit, refer to "CC-Link Unit Intelligent Device Station Hardware Manual".SeriesCPULink I/FCommunication TypeSetting ExampleCable Diagram

文哥
文哥
  • 4231

    文档
  • 0

    金币
Ta的主页 发私信

4231篇文档

文档介绍: CC-Link Partner Association CC-Link Intelligent Device

评论

发表评论
< /44 > 付费下载 ¥ 1 元

Powered by DS文库

Copyright © 联智博库 All Rights Reserved. 鲁ICP备18004091号-4
×
保存成功