您好,欢迎访问联智博库

上传文档

当前位置:首页 > 工控技术 > PLC > CompactLogix System Quick Start

CompactLogix System Quick Start

  • 小库
  • 29 人阅读
  • 0 人下载
  • 2019-02-20 11:07:07

还剩... 页未读,继续阅读

免费阅读已结束,点击付费阅读剩下 ...

¥ 0 元,已有29人购买

免费阅读

阅读已结束,您可以下载文档离线阅读

¥ 1 元,已有0人下载

付费下载

文档部分内容文本提取

CompactLogix SystemCatalog Numbers 1769-L31, 1769-L32C, 1769-L32E, 1769-L35CR, 1769-L35E CompactLogix Controllers, POINT I/O Modules, PowerFlex 70 Drives, PowerFlex 40 Drives, PanelView Plus TerminalsQuick StartImportant User InformationSolid state equipment has operational characteristics differing from those of electromechanical equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls (publication SGI-1.1 available from your local Rockwell Automation sales office or online at http://www.rockwellautomation.com/literature/) describes some important differences between solid state equipment and hard-wired electromechanical devices. Because of this difference, and also because of the wide variety of uses for solid state equipment, all persons responsible for applying this equipment must satisfy themselves that each intended application of this equipment is acceptable.In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages resulting from the use or application of this equipment.The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and requirements associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility or liability for actual use based on the examples and diagrams.No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or software described in this manual.Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell Automation, Inc., is prohibited.Throughout this manual, when necessary, we use notes to make you aware of safety considerations.Allen-Bradley, Rockwell Automation, Rockwell Software, CompactLogix, ControlNet, EtherNet/IP, DeviceNet, PowerFlex 40, PowerFlex 70, POINT I/O, RSLinx, PanelView Plus, RSNetWorx for DeviceNet, RSLogix 5000, RSView Studio, and TechConnect are trademarks of Rockwell Automation, Inc.Trademarks not belonging to Rockwell Automation are property of their respective companies.WARNINGIdentifies information about practices or circumstances that can cause an explosion in a hazardous environment, which may lead to personal injury or death, property damage, or economic loss.IMPORTANTIdentifies information that is critical for successful application and understanding of the product.ATTENTIONIdentifies information about practices or circumstances that can lead to personal injury or death, property damage, or economic loss. Attentions help you identify a hazard, avoid a hazard, and recognize the consequenceSHOCK HAZARDLabels may be on or inside the equipment, for example, a drive or motor, to alert people that dangerous voltage may be present.BURN HAZARDLabels may be on or inside the equipment, for example, a drive or motor, to alert people that surfaces may reach dangerous temperatures.3Publication IASIMP-QS001C-EN-P - October 20093Where to StartFollow the path that matches your hardware and network configuration.Chapter 10Create a Project Using RSLogix 5000 Programming SoftwareChapter 1Prepare the CompactLogix HardwareChapter 2Prepare the ComputerChapter 3Prepare the Distributed POINT I/O HardwareChapter 4Prepare the PowerFlex 70 DriveChapter 5Prepare the PowerFlex 40 DriveChapter 6 Prepare the PanelView Plus TerminalChapter 7Configure the EtherNet/IP NetworkChapter 8Configure the ControlNet DriverChapter 9Configure the DeviceNet NetworkChapter 11Add Distributed I/O Modules to the ProjectChapter 12Create a PowerFlex 70 ApplicationChapter 13Create a PowerFlex 40 ApplicationChapter 14Create a PanelView Plus ApplicationRequiredRequiredOptionalDepending on your system.OptionalDepending on your networks.RequiredOptionalDepending on your system.page17page27page55page63page47page71page81page87page91page99page113page143page167page1894 Publication IASIMP-QS001C-EN-P - October 2009Where to StartHow Hardware is ConnectedThis quick start demonstrates the following possible control systems. Choose your hardware and networks, then follow the matching examples.Option 1: 1769-L32E, 1769-L35E Control SystemPanelView Plus terminal with built-in EtherNet/IPEthernet Switch1769-L32E or 1769-L35E with Optional 1769-SDN for the DeviceNet NetworkSerial (CP3 Cable)PowerFlex 70 Drive with 20-COMM-EPowerFlex 40 Drive with 22-COMM-EPanelView Plus Terminal with Built-in EtherNet/IP PortComputer with Standard Ethernet PortDistributed POINT I/O Modules with 1734-AENTPublication IASIMP-QS001C-EN-P - October 20095Where to StartOption 2: 1769-L32C, 1769-L35CR Control SystemOption 3: 1769-L31 Control SystemControlNet Network with Taps1769-L32C or 1769-L35CR with Optional 1769-SDN for the DeviceNet NetworkPowerFlex 70 Drive with 20-COMM-CPowerFlex 40 Drive with 22-COMM-CPanelView Plus Terminal with ControlNet Communication AdapterComputer with 1784-PCIC, -PCICS ControlNet Communication CardDistributed 1734 POINT I/O Modules with 1734-ACNRSerial (CP3 Cable)To Optional DeviceNet Network1769-L31 with 1769-SDN1756-CP3 Serial Cable to CH0on 1769-L31DeviceNet Network with KwikLink Flat Cable and Micro ConnectorsPowerFlex 70 Drive with 20-COMM-DPowerFlex 40 Drive with 22-COMM-DPanelView Plus Terminal with 2706-NC13 Serial Cable to CH1on 1769-L31Distributed 1734 POINT I/O Modules with 1734-ADNDeviceNet Power Supply 1606-XLDNET8

小库

523篇文档

文档介绍: CompactLogix System Quick Start

评论

发表评论
< /219 > 付费下载 ¥ 1 元

Powered by DS文库

Copyright © 联智博库 All Rights Reserved. 鲁ICP备18004091号-4
×
保存成功